Shipping FREE on all orders over £75 - 
These are single and two speed centre discharge pumps, all the options have 1.5 inch (inlet) x 1.5 inch (outlet).
This European spec. motor (EMG) is recommended by Waterway for the European market, It has a rear fan and a finned body design to dissipate heat.
There are both 1 and 2 speeds available in 48 frame with a 1.5hp and 2hp option on each.
The pumps are supplied without a cable, as the power cord is dedicated to your model of control system, therefore you will need to rewire your existing cable to the pump. Remove the cord from your old pump, and note, the wire colour going to high speed or low speed terminals on any motor, the colour is set or determined by the maker of the spa control, not by the pump or motor manufacturer.
Before you remove the power cord from your old pump, look at the old motor wiring label and make a note of what color goes to high, and to low. Then, put the cord on your new motor/pump, using the same color for high as on the old motor and also for low speed wiring.
Please note if your pump is the red one shown in the photo above then this is the option for you - just pick whether it is 1 or 2 speed - the horse is dependant on the amp draw - please see Hot Tub Pump Identification
This European spec. motor (EMG) is recommended by Waterway for the European market, It has a rear fan and a finned body design to dissipate heat.
There are both 1 and 2 speeds available in 48 frame with a 1.5hp and 2hp option on each.
| 1 Speed | 2 Speed | |
| Length: | 370 mm | 370 mm |
| Height: | 200 mm | 220 mm |
| Width: | 175 mm | 175 mm |
| 1.5HP - Single Speed | 1.5HP - Two Speed | 2HP - Single Speed | 2HP - Two Speed | |
| Amps: | 6 | 2.2 (low) / 6.8 (high) | 6 | 2.2 (low) / 6.8 (high) |
| Volts: | 230 | 230 | 230 | 230 |
| Hz: | 50 | 50 | 50 | 50 |
| Motor KW: | 1.4 | 0.44 (low) / 1.48 (high) | 1.4 | 0.44 (low) / 1.48 (high) |
| HP: | 1.5 | 0.63 (low) / 2.11 (high) | 1.5 | 0.63 (low) / 2.11 (high) |
| Impellor: | 1.5hp (310-5140) | 1.5hp (310-5140) | 2hp (310-5200) | 2hp (310-5200) |
| RPM: | 2820 | 1440 (low) / 2850 (high) | 2820 | 1440 (low) / 2850 (high) |
| Capacitor: | 25uf | 16uf (low) / 30uf (high) | 25uf | 16uf (low) / 30uf (high) |
| Fittings: | 1.5 x 1.5 inch | 1.5 x 1.5 inch | 1.5 x 1.5 inch | 1.5 x 1.5 inch |
The pumps are supplied without a cable, as the power cord is dedicated to your model of control system, therefore you will need to rewire your existing cable to the pump. Remove the cord from your old pump, and note, the wire colour going to high speed or low speed terminals on any motor, the colour is set or determined by the maker of the spa control, not by the pump or motor manufacturer.
Before you remove the power cord from your old pump, look at the old motor wiring label and make a note of what color goes to high, and to low. Then, put the cord on your new motor/pump, using the same color for high as on the old motor and also for low speed wiring.
Please note if your pump is the red one shown in the photo above then this is the option for you - just pick whether it is 1 or 2 speed - the horse is dependant on the amp draw - please see Hot Tub Pump Identification