JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser.
Call Us: 01746 330950
01746 330950Contact us on: 01746 330950
The New Aquaspeed Pump fits perfectly to the original Aquaspeed footprint & pipework connections. This can also be used to replace the Waterco Supatuf Mk2 pumps it has the same spacing on suction and discharge.
In-stock orders dispatched:14:00
Certikin Aquaspeed pumps are one of their most popular pumps, as well as a modern look, the new Aquaspeed model has an upgraded motor manufactured using the latest technology to provide an efficient and powerful pump.
Certikin Aquaspeed Pumps - Variable & 2 SpeedThe Aquaspeed 100 ECO-V pump is the latest addition to the already existing range of Aquaspeed pumps. With all the features and benefits if the renowned Aquaspeed Pump range, the ECO-V brings variable speed economy to an industrial favourite.The Aquaspeed 100 ECO-V is equipped with a state of the art variable speed, permanent magnet brushless motor that results in the ability to vary the motor speed depending on the installation which in turn varies the water flow resulting in a reduction of energy consumption.Ideal for new installations or retro fit as the connections are exactly the same as the single speed Aquaspeed.
• Solid clear pump lid for easy inspection of the basket• Comes complete with 2” quick connect unions for ease of installation (0.5hp, 0.75hp & 1hp are supplied with 1.5” reducers).• 316 high grade mechanical seal• Suitable for salt chlorinated pools• Hydraulically efficient impeller and diffuser design for maximum hydraulic output whilst minimising turbulence• Single piece fibreglass filled pump body to ensure maximum strength and durability• UV stabilised and corrosion resistant pump body• TUV approved• Exclusive to Certikin• P2 rated capacitor (single phase only)• Straight swap for all old style Aquaspeed pumps
1. The pump suction line should not be smaller than the unions supplied with the pump2. The suction line is to have as few bends or elbows as possible. There must not be an air trap on the suction line3. Use only the pump barrel unions supplied with the pump4 Bolt the pump to the required position to prevent movement5. The pump electrical cable must be wired for the proper voltage and rotation in accordance with the wiring instructions6. All wiring (electrical) work must be carried out by a licensed electrician and must be installed in accordance to the local codes7. The motor must be grounded8. The weight of the plumbing and fittings is to be independently supported and not carried by the pump9. The pump motor cooling fan must have a minimum clearance of 150mm
The Aquaspeed pump will prime and re-prime providing the hair and lint pot bowl is full of water and there is sufficient supply from the suction point.If you lose water from the hair and lint pot bowl it will be necessary to refill it before starting.1. Remove the clear lid and fill the hair and lint pot bowl with water2. Replace the lid ensuring the o-ring is correctly located and start the pumpAfter you have done this allow a maximum of 2 minutes for the pump to start delivering water.
Never work on a pump without turning the power offThe strainer basket in the hair and lint pot bowl should be inspected and cleaned at regular intervals.1. Remove lid and lift out basket2. Remove debris and hose off with clean water if necessary3. Inspect the lid gasket, if needed lubricate with silicone based grease only or if damaged replace4. Replace the strainer5. Re-prime the hair and lint pot bowl6. Correctly locate the o-ring7. Replace the lid, tighten by hand only8. Switch on pumpIn climates where the pump may be exposed to frost or freezing, care must be taken to ensure the pump is protected from damage.It is recommended that if the pump is not used during this winter period it should be drained completely. A drain plug is provided for this purpose.Do not replace the drain plug. Store it in a safe place until you require the use of the pump. (An example would be within the hair and lint pot bowl basket.)If at all possible remove the pump away and store it in a dry location during this period.When you reactivate the pump ensure all seals and o-rings are in operational condition, re-grease if necessary and replace if unsure of condition.• Check that the motor shaft moves freely before reactivation
please click here for spare parts
- Each pump comes complete with built on socket unions- The Aquaspeed pump is NOT compatible with Baquacil- 3 phase and 2 speed pumps are supplied without cable
NOTE: Please ensure you order the correct item as a re stocking fee may incur if returned.
Starting at £13.75 £11.46
Starting at £1,628.64 £1,357.20
Max file size: 6 Mb
Follow us on